On a four-color web offset press the paper travels from the unwinder to the folder at several hundred meters per minute. Along that path it is braked, pulled, guided, printed, dried and folded, and every one of those operations acts on the same strip of paper. Tension is the variable that ties them together. When it drifts, register moves, cutoff length changes, and the web starts to wrinkle or break.

A tension system is a chain rather than a single device. It combines brakes, driven rollers, dancer rolls and position sensors, each set to hold a target value while the roll diameter shrinks and the press changes speed. The sections below describe how that chain is arranged on a multi-color web offset press and what each part does.

Three Variables That Move Together

Three quantities govern web behavior: tension, web speed and the elastic modulus of the paper. They are linked. A change in any one of them shifts the other two, which is why the tension loop has to be designed around the whole press instead of around a single roll stand.

Paper is not a perfectly elastic material. It creeps under sustained load, it responds differently along and across the grain, and its modulus varies with moisture. A control system that holds tension accurately at a steady speed can still lose several percent during an acceleration ramp. Operators see this as a slow register drift that appears only after a speed change.

Five Zones Where Tension Is Held

On a multi-color machine the control region is normally divided into five parts: the paper supply at the unwinder, the infeed unit, the printing units, the run from the last printing unit to the chill rolls, and the run from the chill rolls to the folder. A multicolor web press carries more zones and tighter targets than a newspaper press, because ink film thickness, register and cutoff length all react to small tension errors.

Each zone has its own setpoint. The printing units form the reference, and the surrounding sections are trimmed against that reference.

Brake Control at the Unwinder

The unwinder is the first and most important link. Its brake sets the tension that everything downstream inherits. Mechanical band brakes, pneumatic brakes and magnetic particle brakes are all in use, and the magnetic particle type is common on multicolor web presses because it can be adjusted electrically over a wide range.

In a typical loop an adjustable setpoint signal defines the target tension, and a load cell or dancer position produces the feedback signal. The difference passes through a voltage amplifier and a power stage to the brake coil, so brake torque follows the error. With constant excitation current the brake torque stays roughly constant while the roll radius falls, and web tension rises in proportion as the radius shrinks. To hold tension flat, the controller has to reduce brake current as the roll unwinds. This is a proportional loop with offset: it settles at a small residual error instead of at zero. Accuracy of 1 to 2 percent is normal on well-maintained equipment.

Short disturbances need different treatment. A machine vibration, a hard acceleration, an emergency stop or an out-of-round roll can spike tension before the brake loop reacts. Dancer rolls with dampers are fitted for exactly this reason. They absorb the transient, and the control loop only has to handle the slow trend underneath it.

The Infeed Unit as a Second Tension Stage

The infeed unit, sometimes called the second tension stage, sits between the unwinder and the first printing unit. It contains a pinch roller pair, a dancer assembly, a variable-speed drive and web guides. Power from the main shaft passes through a timing belt and a harmonic drive to the driven roller. A tachogenerator reports roller speed, and a differential cylinder engages or releases the pinch roller.

With the pinch roller open, during web-up, the driven roller cannot pull the paper. Once the rollers close, they grip the web and pull it forward, and the speed setting on the driven roller becomes the tension setting for the span ahead. Trimming that speed is how the operator matches the infeed to the printing units.

The dancer roll closes the loop mechanically. A sensing plate rests at a neutral position when tension is correct. If tension rises, the dancer is pulled upward, the support arm rotates, and the plate deflects against a stop. The deflection produces a control signal that reduces tension until the plate returns to neutral. Low tension reverses the sequence. Because the correction is continuous, the dancer doubles as a visual indicator: a dancer sitting far from center tells the operator that the setpoint is wrong, rather than that the loop is slow.

Holding the Web on Centerline

Tension control and web guiding are separate jobs, and both are needed. The infeed guide uses edge or centerline sensors to steer the web with a tilt roller. Correction speed is proportional to the measured offset, so a large error from a bad splice is removed quickly while small errors are trimmed gradually without setting up an oscillation.

On a well-set machine the automatic centering system aligns the tilt roller and the scanner without operator input. With mechanical accuracy near 0.02 mm and working accuracy near 0.127 mm, the web stays inside the tolerance the printing units need. A web that wanders will wrinkle at the nip even when average tension is correct, so guide performance shows up in the waste count as much as in the register.

Setting Section Speeds Against the Printing Cylinder

Multicolor web presses usually run offset and coated stock at roughly 10 to 15 kgf of web tension at the unwinder. That figure is a starting point, not a specification. Final settings come from the printing units, because those cylinders determine register. From there the surrounding sections are trimmed in small increments: the infeed drive runs 0.2 to 0.3 percent slower than the printing cylinder surface, the chill roller and the former roller above the triangle run 0.2 to 0.3 and 0.3 to 0.35 percent slower, and the folder cylinder runs about 0.5 percent faster.

These offsets are small on purpose. They set tension in each span without changing the amount of paper consumed. Surface speed of the driven roller in each zone is the adjustment; measured tension is the feedback. When both agree, register holds through the run and cutoff length stays stable from the first impression to the last.

What Operators Check First

Most tension faults show up as symptoms somewhere else on the press. Register that drifts only after a speed change points to a brake loop that is too slow or a dancer damper that has failed. Wrinkles at the first nip point to the guide. Cutoff length that creeps over a long run usually means the infeed setpoint no longer matches the printing units. Checking dancer position, brake current against roll diameter, and section speed offsets in that order isolates the cause faster than adjusting tension by feel.

None of these settings stay correct on their own. Roll cores vary, splice tape adds thickness, and dampers lose oil over time, so the loop that was flat last month may carry a small offset today. A short weekly check of dancer center position at two speeds catches most of that drift before it reaches the waste pile.